TL-MC-1S1R

Introduction

The TL-MC-1S1R features one SFP port (SFP module sold separately) and one RJ45 twisted pair port, effectively adapting twisted pair-based devices to fiber for longer transmission distances. The MC-1S1R supports multimode fiber when paired with a multimode SFP module and single mode fiber when paired with a single mode SFP module. 

Two TL-MC-1S1R media converters are required for most applications -- one for each end of the cable run. 

 

Features

• Convert signals from twisted pair to fiber and vice versa
• One SFP (fiber) port and one RJ45 (twisted pair) port
• 10/100/1000M data rate
• 850nm/1310nm/1550nm supported wavelengths
• Single mode and multimode fiber compatible (SFP module dependent)
• SFP module sold separately 
• Suggested multimode module: TL-1GSFP-MM550
• Multimode max distance: 550m (1,805 ft.)
• Suggested single mode module: TL-1GSFP-SM20K
• Single mode max distance: 20km (12.4 miles)
• 0 degree to 60 degree C operating temperature
• 1.0" x 2.75" x 3.6" (26mm x 70mm x 93mm)
• 5V power supply (included)
• IEEE 802.3z & 802.3ab compliant
• MDI/MDIX auto-crossover
• Jumbo frame (64-9216 byte)
• Voltage monitor support
• Diagnostic LEDs
• Plug-and-play compliant

 

Package Contents

• [1] TL-MC-1S1R media converter
• [1] Power Supply with International Pins

 

Panel Description

Front

• SFP Port - Insert an SFP module (1G bandwidth) according to the fiber type (single mode or multimode).
• LED Indicators - these report operational status

LED	Status	Operational Status
1000M	On Off	1G Link established 1G Link NOT established
100M	On Off	10/100M Link Established 10/100M Link NOT established
SFP Link/ACT	Blinking Off	Data is transferring through the SFP Module *Data id NOT transferring through the SFP Module
UTP Link/Act	Blinking Off	Data is transferring through the UTP cable Data id NOT transferring through the UTP cable
FDX	On Off	Full Duplex mode enabled on the SFP Full Duplex mode disabled on the SFP
PWR	On Off	Power supply is connected No power supply is connected

*This can be an indication of bad fiber cable or incorrect polarity on a duplex SFP

• UTP Port - Connect to a network device (i.e. network switch or IP camera) using standard network patch cable

Rear

DC 5V - Connect included DC 5V/1A power adaptor

System Connection

There are several applications suitable for media converters, here are a few examples:

Example 1 - extend from network switch with SFP module.

In this example, the network switch includes an SFP module and the media converter is utilizing the fiber optic cable to extend the LAN signal to the IP camera.

*The TL-MC-1S1R does not offer PoE so the camera must be powered locally. 

Example 2 - extend LAN signal using switch without SFP ports.

In this example, the network switch does not offer an SFP module. Using [2] media converters allows fiber optic cabling to be utilized.

*The TL-MC-1S1R does not offer PoE so the camera must be powered locally. 

Specifications

I/O Connections
Fiber Module Port	SFP (small form-factor pluggable) connector port
UTP	8p8c unshielded female connector
DC 5V	Female coaxial barrel connector - 5.5mm O.D. x 2.5mm I.D.
Signal Characteristics
SFP compatibility	IEEE 802.3z/AB 1000Base-T/SX/LX/ZX TLN Part #s: TL-1GSFP-MM550 - Multimode Fiber TL-1GSFP-SM20K - Single Mode Fiber
Link Support	IEEE 802.3X Full Duplex and Half Duplex with flow control MDI/MDI-X automatic switching
Jumbo Frame	Supported Jumbo frame (64-9216 byte)
Chassis and Environmental
Enclosure	Painted Steel
Dimensions	1.0" x 2.75" x 3.6" (26mm x 70mm x 93mm)
Dimensions (Shipping)	7.25" x 6" x 2" (184mm x 70 x 51mm)
Weight (Shipping)	355g
Working Temperature	0°C~60°C
Operating Humidity	5%~90%
Power Supply
Input Voltage	100~240v AC, 50~60Hz, 0.3A
Output Voltage	5VDC Center Positive 1.2A
Regulatory	CE, FCC, RoHS, WEE, UL-US, UL-C, CCC, JET, C-TICK, UL-DE/GS
Efficiency	Level VI
Other
Warranty	3 Years
Package Contents	[1] TL-MC-1S1R [1] 5VDC Power Supply (USA, AUS, EU, UK Pins)

Go to product page...